One more step towards BSP thread-safety. This one brought with it a very
noticeable speed boost (ie, not lost in the noise) thanks to the face
visframes being in tightly packed groups instead of 128 bytes apart,
though the sw render's boost is lost in the noise (but it's very
fill-rate limited).
This is next critical step to making BSP rendering thread-safe.
visframe was replaced with cluster (not used yet) in anticipation of BSP
cluster reconstruction (which will be necessary for dealing with large
maps like ad_tears).
The main goal was to get visframe out of mnode_t to make it thread-safe
(each thread can have its own visframe array), but moving the plane info
into mnode_t made for better data access patters when traversing the bsp
tree as the plane is right there with the child indices. Nicely, the
size of mnode_t is the same as before (64 bytes due to alignment), with
4 bytes wasted.
Performance-wise, there seems to be very little difference. Maybe
slightly slower.
The unfortunate thing about the change is the plane distance is negated,
possibly leading to some confusion, particularly since the box and
sphere culling functions were affected. However, this is so point-plane
distance calculations can be done with a single 4d dot product.
The map uses 41% of a 4k light map scrap, and 512 texture descriptors
wasn't enough for vulkan. Ouch. I do need to get cvars on these things,
but this will do for now (decades later...)
This was one of the biggest reasons I had trouble understanding the bsp
display list code, but it turns out it was for dealing with GLES's
16-bit limit on vertex indices. Since vulkan uses 32-bit indices,
there's no need for the extra layer of indirection. I'm pretty sure it
was that lack of understanding that prevented me from removing it when I
first converted the glsl bsp code to vulkan (ie, that 16-bit indices
were the only reason for elements_t).
It's hard to tell whether the change makes much difference to
performance, though it seems it might (noisy stats even over 50 timedemo
loops) and the better data localization indicate it should at least be
just as good if not better. However, the reason for the change is
simplifying the data structures so I can make bsp rendering thread-safe
in preparation for rendering shadow maps.
And maybe a nano-optimization. Switching from (~side + 1) to (-side)
seems to give glsl a very tiny speed boost, but certainly doesn't hurt.
Looking at some assembly output for the three cases, the two hacks seem
to generate the same code as each other, but 3 instructions vs 6 for ?:.
While ?: is more generically robust, the hacks are tuned for the
knowledge side is either 0 or 1. The later xor might alter things, but
at least I now know that the hack (either version) is worthwhile.
With experience, I have found that trying to continue after a validation
error tends to result in a segfault or some other nastiness, and
Sys_Shutdown (and the full shutdown sequence) is triggered for any error
signal (segfault, abort, etc) so just exit(1).
Some very much needed comments :P Still, nicely, I now have a much
better understanding of how the display lists are created (10 years
is a long time to remember how intricate code works (I do remember
fighting to get it working back then))
This makes it much easier to see just what is being done to build a
polygon to be passed to the GPU, and it served as a test for the
lightmap st changes since Vulkan currently never used them.
Many modders use negative lights for interesting effects, but vulkan
doesn't like the result of a negative int treated as unsigned when it
comes to texture sizes.
However, this time it doesn't modify the light array when it sorts the
lights by size since the lights are now located before the renderer gets
to see them, and having the fix up the light leafs array would be too
painful (and probably the completely wrong thing to do anyway: the light
array should be treated as constant by the renderer). 1.6GB of memory
for gmsp3v2's lights (a little better than marcher: more smaller lights?).
For reference:
gmsp3v2: shadow maps: 8330 layers in 29 images: 1647706112
marcher: shadow maps: 2440 layers in 11 images: 2358575104
For now, at least (I have some ideas to possibly reduce the numbers and
also to avoid the need for actual limits). I've seen gmsp3v2 use over
500 lights at once (it has over 1300), and I spent too long figuring out
that weird light behavior was due to the limit being hit and lights
getting dropped (and even longer figuring out that more weird behavior
was due to the lack of shadows and the world being too bright in the
first place).
Since the staging buffer allocates the command buffers it uses, it
needs to free them when it is freed. I think I was confused by the
validation layers not complaining about unfreed buffers when shutting
down, but that's because destroying the pool (during program shutdown,
when the validation layers would complain) frees all the buffers. Thus,
due to staging buffers being created and destroyed during the level load
process, (rather large) command buffers were piling up like imps in a
Doom level.
In the process, it was necessary to rearrange some of the shutdown code
because vulkan_vid_render_shutdown destroys the shared command pool, but
the pool is required for freeing the command buffers, but there was a
minor mess of long-lived staging buffers being freed afterwards. That
didn't end particularly well.
This is meant for a "permanent" tear-down before freeing the memory
holding the VM state or at program shutdown. As a consequence, builtin
sub-systems registering resources are now required to pass a "destroy"
function pointer that will be called just before the memory holding
those resources is freed by the VM resource manager (ie, the manager
owns the resource memory block, but each subsystem is responsible for
cleaning up any resources held within that block).
This even enhances thread-safety in rua_obj (there are some problems
with cmd, cvar, and gib).
This gives a rather significant speed boost to timedemo demo1: from
about 2300-2360fps up to 2520-2600fps, at least when using
multi-texture.
Since it was necessary for testing the scrap, gl got the ability to set
the console background texture, too.
While it takes one extra step to grab the marksurface pointer,
R_MarkLeaves and R_MarkLights (the two actual users) seem to be either
the same speed or fractionally faster (by a few microseconds). I imagine
the loss gone to the extra fetch is made up for by better bandwidth
while traversing the leafs array (mleaf_t now fits in a single cache
line, so leafs are cache-aligned since hunk allocations are aligned).
Unfortunately, the animations are pre-baked (by the loader) blocking
run-time determined animations (IK etc). However, this at least gets
everything working so the basics can be verified (the shader posed some
issue resulting in horror movies ;).
Brush models looked a little too tricky due to the very different style
of command queue, so that's left for now, but alias, iqm and sprite
entities are now labeled. The labels are made up of the lower 5 hex
digits of the entity address, the position, and colored by the
normalized position vector. Not sure that's the best choice as it does
mean the color changes as the entity moves, and can be quite subtle
between nearby entities, but it still helps identify the entities in the
command buffer.
And, as I suspected, I've got multiple draw calls for the one ogre. Now
to find out why.
The bones aren't animated yet (and I realized I made the mistake of
thinking the bone buffer was per-model when it's really per-instance (I
think this mistake is in the rest of QF, too)), skin rendering is a
mess, need to default vertex attributes that aren't in the model...
Still, it's quite satisfying seeing Mr Fixit on screen again :)
I wound up moving the pipeline spec in with the rest of the pipelines as
the system isn't really ready for separating them.
The plists can now be accessed by name and the forward render pass
config is available (but not used, or tested beyond syntax). I was going
to have the IQM pipeline spec separate but ran into limitations in the
system (which needs a lot of polish, really).
That @inherit is pretty useful :) This makes it much easier to see how
different pipelines differ or how they are the similar. It also makes it
much clearer which sub-pass they're for.
I was wondering why scaled-down quake-guy was dimmer than full-size
quake-guy. And the per-fragment normalization gives the illusion of
smoothness if you don't look at his legs (and even then...).
I'm not sure what's up with the weird lighting that results from dynamic
lights being directional (sunlight works nicely in marcher, but it has a
unit vector for position).
The parsing of light data from maps is now in the client library, and
basic light management is in scene. Putting the light loading code into
the Vulkan renderer was a mistake I've wanted to correct for a while.
The client code still needs a bit of cleanup, but the basics are working
nicely.
This replaces *_NewMap with *_NewScene and adds SCR_NewScene to handle
loading a new map (for quake) in the renderer, and will eventually be
how any new scene is loaded.
This leaves only the one conditional in the shader code, that being the
distance check. It doesn't seem to make any noticeable difference to
performance, but other than explosion sprites being blue, lighting
quality seems to have improved. However, I really need to get shadows
working: marcher is just silly-bright without them, and light levels
changing as I move around is a bit disconcerting (but reasonable as
those lights' leaf nodes go in and out of visibility).
Id Software had pretty much nothing to do with the vulkan renderer (they
still get credit for code that's heavily based on the original quake
code, of course).
It's not used yet, and thus may have some incorrect settings, but I
decided that I will probably want it at some stage for qwaq. It's
essentially was was in the original spec, but updated for some of the
niceties added to parsing since I removed it back then. It's also in its
own file.
Despite the base IQM specification not supporting blend-shapes, I think
IQM will become the basis for QF's generic model representation (at
least for the more advanced renderers). After my experience with .mu
models (KSP) and unity mesh objects (both normal and skinned), and
reviewing the IQM spec, it looks like with the addition of support for
blend-shapes, IQM is actually pretty good.
This is just the preliminary work to get standard IQM models loading in
vulkan (seems to work, along with unloading), and they very basics into
the renderer (most likely not working: not tested yet). The rest of the
renderer seems to be unaffected, though, which is good.
The resource subsystem creates buffers, images, buffer views and image
views in a single batch operation, using a single memory object to back
all the buffers and images. I had been doing this by hand for a while,
but got tired of jumping through all those vulkan hoops. While it's
still a little tedious to set up the arrays for QFV_CreateResource (and
they need to be kept around for QFV_DestroyResource), it really eases
calculation of memory object size and sub-resource offsets. And
destroying all the objects is just one call to QFV_DestroyResource.
Vulkan doesn't appreciate the empty buffers that result from the model
not having any textures or surfaces that can be rendered (rightfully so,
for such a bare-metal api).
I doubt the calls were ever actually made in a normal map due to the
node actually being a node when breaking out of the loop, but when I
experimented with an empty world model (no nodes, one infinite empty
leaf) I found that visit_leaf was getting called twice instead of once.
Since it is updated every frame, it needs to be as fast as possible for
the cpu code. This seems to make a difference of about 10us (~130 ->
~120) when testing in marcher. Not a huge change, but the timing
calculation was wrapped around the entire base world pass, so there was
a fair bit of overhead from bsp traversal etc.
It makes a significant difference to level load times (approximately
halves them for demo1 and demo2). Nicely, it turns out I had implemented
the rest of the staging buffer code (in particular, flushing) correctly
in that it seems there's no corruption any of the data.
The misinterpretations were due to either the cvar not being accessed
directly by the engine, but via only the callback, or the cvars were
accesssed only by progs (in which case, they should be float). The
remainder are a potential enum (hud gravity) and a "too hard basket"
(rcon password: need to figure out how I want to handle secret strings).
This is an extremely extensive patch as it hits every cvar, and every
usage of the cvars. Cvars no longer store the value they control,
instead, they use a cexpr value object to reference the value and
specify the value's type (currently, a null type is used for strings).
Non-string cvars are passed through cexpr, allowing expressions in the
cvars' settings. Also, cvars have returned to an enhanced version of the
original (id quake) registration scheme.
As a minor benefit, relevant code having direct access to the
cvar-controlled variables is probably a slight optimization as it
removed a pointer dereference, and the variables can be located for data
locality.
The static cvar descriptors are made private as an additional safety
layer, though there's nothing stopping external modification via
Cvar_FindVar (which is needed for adding listeners).
While not used yet (partly due to working out the design), cvars can
have a validation function.
Registering a cvar allows a primary listener (and its data) to be
specified: it will always be called first when the cvar is modified. The
combination of proper listeners and direct access to the controlled
variable greatly simplifies the more complex cvar interactions as much
less null checking is required, and there's no need for one cvar's
callback to call another's.
nq-x11 is known to work at least well enough for the demos. More testing
will come.
This allows for easy (and safe) printing of cexpr values where the type
supports it. Types that don't support printing would be due to being too
complex or possibly write-only (eg, password strings, when strings are
supported directly).
Surprisingly, only two, but they were caught by the different value
fields being used, thus the cvar was checked in multiple places. I
imagine that's not really all that common, so there may be some
inconsistencies between default value and use.
This allows a single render pass description to be used for both
on-screen and off-screen targets. While Vulkan does allow a VkRenderPass
to be used with any compatible frame buffer, and vkparse caches a
VkRenderPass created from the same description, this allows the same
description to be used for a compatible off-screen target without any
dependence on the swapchain. However, there is a problem in the caching
when it comes to targeting outputs with different formats.
As I had suspected, it's due to a synchronization problem between the
scrap and drawing. There's actually a double problem in that data
uploaded to the scrap isn't flushed until the first frame is rendered
causing a quick init-shutdown sequence to take at least five seconds due
to the staging buffer waiting (and timing out) on a stuck fence.
Rendering just one frame "fixes" the problem (draw was one of the
earliest subsystems to get going in vulkan).
Surprisingly, only two, but they were caught by the different value
fields being used, thus the cvar was checked in multiple places. I
imagine that's not really all that common, so there may be some
inconsistencies between default value and use.
Since it is updated every frame, it needs to be as fast as possible for
the cpu code. This seems to make a difference of about 10us (~130 ->
~120) when testing in marcher. Not a huge change, but the timing
calculation was wrapped around the entire base world pass, so there was
a fair bit of overhead from bsp traversal etc.
Really, this won't make all that much difference because alias models
with more than one skin are quite rare, and those with animated skin
groups are even rarer. However, for those models that do have more than
one skin, it will allow for reduced allocation overheads, and when
supported (glsl, vulkan, maybe gl), loading all the skins into an array
texture (since all skins are the same size, though external skins may
vary), but that's not implemented yet, this just wraps the old one skin
at a time code.
While looking at the deferred attachment images with using a template in
mind, I noticed that the opaque attachment was using 8-bit color. The
problem is, it's meant to be HDRI with the compose pass crunching it
down to LDRI. Switching to 16-bit float does seem to have made a subtle
difference (hey, it's still quake data, not much HDRI in there).
That certainly makes it nicer to work with large sets, and shows one way
to be careful with allocated resources: don't allocate them in the
inherited data and use a template that needs a few things filled in to
be valid. Also, it seems that overriding values in sub-structures "just
works" :)
It simply parses the referenced plist dictionary (via @inherit =
plist.path;) into the current data block, then allows the data to be
overwritten by the current plist dictionary. This may be a bit iffy for
any allocated resources, so some care must be taken, but it seems to
work nicely.
This allows a single render pass description to be used for both
on-screen and off-screen targets. While Vulkan does allow a VkRenderPass
to be used with any compatible frame buffer, and vkparse caches a
VkRenderPass created from the same description, this allows the same
description to be used for a compatible off-screen target without any
dependence on the swapchain. However, there is a problem in the caching
when it comes to targeting outputs with different formats.
This makes much more sense as they are intimately tied to the frame
buffer on which a render pass is working. Now, just the window width
and height are stored in vulkan_ctx_t. As a side benefit,
QFV_CreateSwapchain no long references viddef (now just palette and
conview in vulkan_draw.c to go).
While I have trouble imagining it making that much performance
difference going from 4 verts to 3 for a whopping 2 polygons, or even
from 2 triangles to 1 for each poly, using only indices for the vertices
does remove a lot of code, and better yet, some memory and buffer
allocations... always a good thing.
That said, I guess freeing up a GPU thread for something else could make
a difference.
I think I had gotten lucky with captures not being corrupt due to them
being much bigger than all but the L3 cache (and then they're over 1/2
the size), so the memory was being automatically invalidated by other
activity. Don't want to trust such luck, though.
It makes a significant difference to level load times (approximately
halves them for demo1 and demo2). Nicely, it turns out I had implemented
the rest of the staging buffer code (in particular, flushing) correctly
in that it seems there's no corruption any of the data.
This means that a tex_t object is passed in instead of just raw bytes
and width and height, but it means the texture can specify whether it's
flipped or uses BGR instead of RGB. This fixes the upside down
screenshots for vulkan.
This fixes (*ahem*) the vulkan renderer segfaulting when attempting to
take a screenshot. However, the image is upside down. Also, remote
snapshots and demo capture are broken for the moment.
QFS_NextFilename was renamed to QFS_NextFile to reflect the fact it now
returns a QFile pointer for the newly created file (as well as the
name). This necessitated updating WritePNG to take a file pointer
instead of a file name, with the advantage that WritePNGqfs is no longer
necessary and callers have much more control over the creation of the
file.
This makes QFS_NextFile much more secure against file system race
conditions and attacks (at least in theory). If nothing else, it will
make it more robust in a multi-threaded environment.
It's not there yet as it promptly closes the file and returns only the
filename (and then only the portion within the user's directory tree).
However, this worked nicely as a test for Sys_UniqueFile.
It seems clang defaults to unsigned for enums. Interestingly, gcc was ok
with the checks being either way. I guess gcc treats enums that *can* be
unsigned as DWIM.
Still work with gcc, of course, and I still need to fix them properly,
but now they're actually slightly easier to find as they all have vec_t
and FIXME on the same line.
Viewport and FOV updates are now separate so updating one doesn't cause
recalculations of the other. Also, perspective setup is now done
directly from the tangents of the half angles for fov_x and fov_y making
the renderers independent of fov/aspect mode. I imagine things are a bit
of a mess with view size changes, and especially screen size changes
(not supported yet anyway), and vulkan winds up updating its projection
matrices every frame, but everything that's expected to work does
(vulkan errors out for fisheye or warp due to frame buffer creation not
being supported yet).
If the entity didn't have a known model type, R_StoreEfrags would get
stuck in an infinite loop (fortunately, never actually happened. The
result of making it not call Sys_Error for unknown models)).
I meant to do this a while ago but forgot about it. Things are a bit of
a mess in that the renderer knows too much about entities, but
eventually the renderer will know about only things to render (meshes,
particles, etc).
The quake-specific enums are now in the client header, and the particle
system now has a gravity field rather than getting it from
vid_render_data (which I hope to eventually get rid of entirely).
r_refdef is really meant for holding the various screen "constants" for
the software renderer rather than the more generic scene stuff. All the
fields referenced by the low level rendering code (especially assembly)
have been moved to the beginning of the struct (and nicely fit within 64
bytes). The other fields should be moved elsewhere, but not this commit.
On top of that, R_ViewChanged is much easier to read, and there are
fewer static globals.
Now GL perspective matrix setup matches that of GLSL and Vulkan, and
GL's z_up matrix matches GLSL's (as it should, since they're really
going through the same API). GL also needs the depth adjustmet matrix
now. Other than having to google the docs for glFrustum, there's nothing
wrong with the function itself, but it's nice to have direct control
over the matrices.
In the process, I discovered how horribly confused I've been at times
with respect to the handedness of GL and Quake: GL is right-handed
(y-up, z-out, x-right), as is Quake itself (but z-up, y-left, x-in), but
as the perspective matrix used in the three renderers expects z-in,
having x-right and y-up makes the matrix effectively left-handed (not
for Vulkan though, because there it's y-down, x-right, z-up, so
right-handed again).
Of course, it's not as correct as glsl or sw due to using polygons and
uvs rather than a fragment shader (not that such is out of the question
since GL 3.0 is requested, but I don't feel like getting shaders going
just for a couple of post-processing effects in an obsolete renderer).
While it's not where I want it to be, it at least now no longer messes
with frame buffer binding or the view ports. This involved switching
around buffers in D_WarpScreen so that the main buffer could be bound
before post-processing.
The cvar setup for particles is a bit wonky in that the arrays get
initialized using the default max particle count but never updated.
Though things could be improved some more, this solution works (and has
been more or less copied to gl, but I couldn't reproduce the crash
there, or even the valgrind error).
The code dealing with state is a bit of a mess, but everything is
working nicely. Get around 400fps when all 6 faces need to be rendered
(no surprise: it should be about 1/6 of that for normal rendering). The
messy state handling code did not come as a surprise as I suspected
there were various mistakes in my scene rendering "recipe", and fisheye
highlighted them nicely (I'm sure getting this stuff working in Vulkan
will highlight even more issues).
Finally, after a decade :P Looks pretty good, too, and is (almost)
properly scaled to the resolution (almost because the effect is a little
squashed, but I think the sw renderer does the same).
The GLSL compiler requires any #version lines to be the first (real)
line of the program, even #line causes an error, so if the first line of
the chunk starts with #version, insert the #line directive as the second
line.
Again, gl/vulkan not working yet (on the assumption that sw would be
trickier).
Fisheye overrides water warp because updating the projection map every
frame is far too expensive.
I've added a post-process pass to the interface in order to hide the
implementation details, but I'm not sure I'm happy about how the
multi-pass rendering for cube maps is handled (or having the frame
buffers as exposed as they are), but mainly because Vulkan will make
implementation interesting.
For now, OpenGL and Vulkan renderers are broken as I focused on getting
the software renderer working (which was quite tricky to get right).
This fixes a couple of issues: the segfault when warping the screen (due
to the scene rendering move invalidating the warp buffer), and warp
always having 320x200 resolution. There's still the problem of the
effect being too subtle at high resolution, but that's just a matter of
updating the tables and tweaking the code in D_WarpScreen.
Another issue is the Draw functions should probably write directly to
the main frame buffer or even one passed in as a parameter. This would
remove the need for binding the main buffer at the beginning and end of
the frame.
This used to be handled by R_RenderView (encompassing all of the
rendering) before the scene rendering was moved out to r_screen. This
fixes the stuck time in 32-bit nq-win.
Its guts have been moved to D_Init temporarily while I work on the
frame buffer design. This is actually a big part of that work as it
moves most of the frame buffer creation into the one place, making it
easier to ensure I get all the sub-buffers and caches created.
With what I have planned for frame buffers etc, GL 3.0 will be needed
even for the fixed-function GL renderer, and then I might even take the
GLSL renderer to 4.6 (dunno yet). This means that wgl will need to be
updated too, and I've found the info I need for that, but it's a bit
much to take on just yet.
I think the widespread use of recalc_refdef (and force_fullscreen) was
the result of a rushed merge of the renderer and video code (I do seem
to remember sprinkling them around). This cleans the two out of the
client code.
This avoids the possibility of a singularity (and thus the temptation to
use Sys_Error). While the rendering is rubbish, 0 degrees is allowed
because values less than 1 should be allowed, but where does one stop?
170 is the maximum in order to avoid any issues with (near) parallel or
inverted frustum planes (or other fun things) in the low level code.
Other than the view model (undecided on the approach) this has
R_RenderView pretty much pulled out of the low level renderers. With
this, I'll be able to focus on scene handling for a bit then getting
shadows and fisheye working (again for fisheye).
r_screen isn't really the right place, but it gets the scene rendering
out of the low-level renderers and will make it easier to sort out
later, and hopefully easier to figure out a good design for vulkan.
gl_overbright_f shouldn't need to run through any entity queues to
update the light maps as only the world model has light maps, and
hitting the world model should hit all its sub-models.
The change to using separate per-model-type entity queues resulted in
the lighting vector used for alias and iqm models being in an ephemeral
location (in the shared setup_lighting function's stack frame). This
resulted in the model rendering code getting a garbage vector due to it
being overwritten by another stack frame. What I don't get is why the
garbage varied from run to run for the same demo (demo2, the first scrag
behind the start door showed the bad lighting nicely), which made
tracking down the offending commit (and thus the code) rather
troublesome, though once I found it, it was a bit of a face-palm moment.
Move r_pcurrentvertbase into the sw renderer, cleaning up gl's use of
(not really needed there). Not ready to move r_bsp into the main bin yet
as there are linking issues since only the low-level code references any
of its symbols.
The code is really part of scene (not a typo wrt r_screen: that is
misnamed as such, or at least SCR_UpdateScreen needs to be split into
screen (2d overlay, really) and scene updates).
This breaks fisheye rendering as the fisheye code calls the actual scene
render code multiple times, but the fisheye code is called by said scene
render code via a diversion. The fisheye needs to be moved out to the
high level scene render, but that will takes some extra work for frame
buffer setup.
The two aren't compatible (but warping might be doable in the fisheye
code). The whole frame setup code needs a rework, and really, even the
buffer handling.
It being on the stack was a bad idea as R_RenderWorld returns before the
scans are rendered and thus the entity pointer winds up pointing to
abandoned stack space.
While the scheme of using our own allocated did work just fine, fisheye
rendering uses glGenTextures which caused a texture id clash and thus
invalid operations (the cube map texture happened to be the same as the
console background texture). Sure, I could have just "fixed" the fisheye
init code, but this brings gl closer in line with glsl (which makes
extensive use of glGenTextures and glDeleteTextures). This doesn't fix
any texture leaks gl has (plenty, I imagine), but it's a step in the
right direction.
Only for gl and sw at the moment (want to merge things further before I
do anything for glsl or vulkan). However, with with I've learned getting
gl and sw to work, glsl and vulkan will be trivial.
R_RecursiveLightUpdate has been obsolete for a very long time, and
R_Mirror is just wrong (needs envmaps etc, wonder if it can be done in
the fixed function code using skyclip?)
Finally. I never liked it (felt bad adding it in the first place), and
it has caused confusion with function and global variable names, but it
did let me get the render plugins working.
This moves the common camera setup code out of the individual drivers,
and completely removes vup/vright/vpn from the non-software renderers.
This has highlighted the craziness around AngleVectors with it putting
+X forward, -Y right and +Z up. The main issue with this is it requires
a 90 degree pre-rotation about the Z axis to get the camera pointing in
the right direction, and that's for the native sw renderer (vulkan needs
a 90 degree pre-rotation about X, and gl and glsl need to invert an
axis, too), though at least it's just a matrix swizzle and vector
negation. However, it does mean the camera matrices can't be used
directly.
Also rename vpn to vfwd (still abbreviated, but fwd is much clearer in
meaning (to me, at least) than pn (plane normal, I guess, but which
way?)).
I'd been considering it for a while, but in the end, all the issues it
presented made me decide it wasn't worth merging and was never really
worth keeping: it was a neat proof of concept but of little actual use,
especially now everyone either has an OK GPU or would want to stick to
8-bit rendering anyway (sorry L-Havoc).
However, both it and my merge work are preserved in git history :)
16 and 32 bit rendering are disabled at the moment because there's a
weird segfault I need to fix, but the 8-bit dynamic lights are doing
weird things (for x11, too) when updating the light maps.
I got tired of having to maintain two separate software renderers, but
didn't want to just nuke sw32, so its core changes are merged into sw.
Alias model rendering is broken, but I know exactly what's wrong and how
to fix it, just need to take care due to asm.
So far, in gl and glsl, but viewposition is much clearer than r_origin
(despite being the same thing), and modelorg is just confusing (I think
it's the view position relative to the current model).
GL still has its own functions for enabling and disabling fog while
rendering, but GLSL doesn't need such (thanks to the shaders), nor will
vulkan (and the software renderers don't support fog).
This is a step towards high-level unification of the renderers, as far
as possible keeping only actual low-level implementation details in the
individual renderers (some higher level stuff, eg shadows, is expected
to be per-renderer as some things are just not feasible to implement in
all renderers). However, the idea is to move the high-level
functionality into scene rendering.
As qwaq doesn't yet do any 3d rendering, it doesn't use efrags and thus
wasn't pulling in the object file, but the various renderers were trying
to access it. And I thought plugin builds were more difficult (I had
forgotten).
Only CaptureBGR is per-renderer as the rest of the screenshot code uses
it to do the actual capture (which is target dependent). Vulkan is
currently broken due to capture being an asynchronous process and the
rest of the code expecting capture to be synchronous (also, bgr vs rgb).
The best thing is all renderers now write the same format (currently
png).
I'm not sure what the author of that code was thinking (maybe trying to
do 4 pixels at a time?), but the resulting code still did only one.
Better to remove all the casts, use the right pointer type, and keep the
code clear.
Drawing sky chains first ensures that sky surfaces correctly block parts
of the map that should not be visible (by writing the correct depth to
the depth buffer when doing box or dome skies). Writing brush models
first means that the models (ammo boxes etc) could be visible when they
should not be.
While there's currently only the one still, this will allow the entities
to be multiply queued for multi-pass rendering (eg, shadows). As the
avoidance of putting an entity in the same queue more than once relies
on the entity id, all entities now come from the scene (which is stored
in cl_world in the client code for nq and qw), thus the extensive
changes in the clients.
GL and GLSL were drawing the view model after particles instead of
before. For GL, this is likely due to avoiding fog affecting the view
model (which I think is not the right thing to do), and GLSL due to
copying GL (because I had no idea at the time). This makes the two
renderers consistent with the software renderers, and might even speed
things up a little as that's one less set of blends to do when the
particles are covered by the view model (I don't expect much
difference).
While I doubt the difference is all that significant, this should speed
up entity rendering because it cuts out a lot of branching, and
eliminates scanning the same list multiple times only to not do anything
for large chunks of the list.
The actual view and projection matrices are now consistent with vulkan,
with the vulkan-gl disparity moved into adjustment matrices. The goal is
to allow the same camera data and code to be used in all renderers. The
extra matrix multiplication shouldn't be too expensive as it occurs only
when the field of view (not often, under user control) or near and far
clip distances (very rarely) change.
While both matrices had positive determinants in the first place, I find
the projection matrix easier to understand without all the negatives,
and having quake-x/vulkan-z positively parallel in the z-up matrix makes
that a lot easier to think about.
Regardless of whether the sky is spinning or not, the matrix needs to be
updated with the current origin in order to get the direction vector
right in the shader. Also, it's in the update that the required x-y
plane rotation gets in so the skies move in the correct direction.
