Because the aliases were treated as live, every alias of a temp resulted
in an assignment, which proved to be quite significant (4-5 assignments
in some simple GA expressions). By using an alias node in the dag, the
unaliased temp can be marked live while the alias is treated as an
operation rather than an operand. Now my GA expressions have no
superfluous assignments (generally no assignments at all).
Simple k-vectors don't use structs for their layout since they're just
an array of scalars, but having the structs for group sets or full
multi-vectors makes the system alignment agnostic.
And geometric algebra vectors. This does break things a little in GA,
but it does bring qfcc's C closer to standard C in that sizeof respects
the alignment of the type (very important for arrays).
It's implemented as the Hodge dual, which is probably reasonable until
people complain. Both ⋆ and ! are supported, though the former is a
little hard to see in Consola.
The singleton alias resulted in the adjusted swizzles being corrupted
when for the same def. Other than adding properly sized swizzles
(planned), the simplest solution is to (separately) allow alias that
stick out from from the def.
Currently via only the group mask (which is really horrible to work
with: requires too much knowledge of implementation details, but does
the job for testing), but it got some basics working.
Also, correct the handling of scalars in dot and wedge products: it
turns out s.v and s^v both scale. However, it seems the CSE code loses
things sometimes.
This makes working with them much easier, and the type system reflects
what's in the multi-vector. Unfortunately, that does mean that large
algebras will wind up having a LOT of types, but it allows for efficient
storage of sparse multi-vectors:
auto v = 4*(e1 + e032 + e123);
results in:
0005 0213 1:0008<00000008>4:void 0:0000<00000000>?:invalid
0:0044<00000044>4:void assign (<void>), v
0006 0213 1:000c<0000000c>4:void 0:0000<00000000>?:invalid
0:0048<00000048>4:void assign (<void>), {v + 4}
Where the two source vectors are:
44:1 0 .imm float:18e [4, 0, 0, 0]
48:1 0 .imm float:1aa [4, 0, 0, 4]
They just happen to be adjacent, but don't need to be.
This gets only some very basics working:
* Algebra (multi-vector) types: eg @algebra(float(3,0,1)).
* Algebra scopes (using either the above or @algebra(TYPE_NAME) where
the above was used in a typedef.
* Basis blades (eg, e12) done via procedural symbols that evaluate to
suitable constants based on the basis group for the blade.
* Addition and subtraction of multi-vectors (only partially tested).
* Assignment of sub-algebra multi-vectors to full-algebra multi-vectors
(missing elements zeroed).
There's still much work to be done, but I thought it time to get
something into git.
If a symbol is not found in the table and a callback is provided, the
callback will be used to check for a valid procedural symbol before
moving on to the next table in the chain. This allows for both tight
scoping of the procedural symbols and caching.
Due to joys of pointers and the like, it's a bit of a bolt-on for now,
but it works nicely for basic math ops which is what I wanted, and the
code is generated from the expression.
I never liked it, but with C2x coming out, it's best to handle bools
properly. I haven't gone through all the uses of int as bool (I'll leave
that for fixing when I encounter them), but this gets QF working with
both c2x (really, gnu2x because of raw strings).
The warning flag check worked too well: it enabled the warning and
autoconf's default main wanted the const attribute. The bug has been
floating around for a while, it seems.
I'm not certain this is correct, but it seems to me that du-chains are
the same information as ud-chains, but from the defining statement's
point of view instead of that of the using statement.
I think the current build_element_chain implementation does a reasonable
job, but I'm in the process of getting designated initializers working,
thus it will become important to ensure uninitialized members get
initialized.
I never liked the various hacks I had come up with for representing
resource handles in Ruamoko. Structs with an int were awkward to test,
pointers and ints could be modified, etc etc. The new @handle keyword (@
used to keep handle free for use) works just like struct, union and
enum in syntax, but creates an opaque type suitable for a 32-bit handle.
The backing type is a function so v6 progs can use it without (all the
necessary opcodes exist) and no modifications were needed for
type-checking in binary expressions, but only assignment and comparisons
are supported, and (of course) nil. Tested using cbuf_t and QFile: seems
to work as desired.
I had considered 64-bit handles, but really, if more than 4G resource
objects are needed, I'm not sure QF can handle the game. However, that
limit is per resource manager, not total.
The first use will be pointer analysis for function arguments where the
argument points to an array to mark the array as live, but I'm sure
there'll be plenty of other uses.
Needed for proper analysis (ud-chains etc). Of course, it was then
necessary to remove the parameter defs from the uninitialized defs.
Also, plug a couple of memory leaks (forgot to free some temporary
sets).
I had messed up the handling of declarators for combinations of pointer,
function, and array: the pointer would get lost (and presumably arrays
of functions etc). I think I had gotten confused and thought things were
a tree rather than a simple list, but Holub set me straight once again
(I've never regretted getting that book). Once I understood that, it was
just a matter of finding all the places that needed to be fixed. Nicely,
most of the duplicated code has been refactored and should be easier to
debug in the future.
The type system rewrite had lost some of the checks for function fields.
This puts the actual code in the one place and covers parameters as well
as globals.
The symtab code itself cares only about global/not global for the size
of the hash table, but other code can use the symtab type for various
checks (eg, parameter shadowing).
Along with QuakeC's, of course. This fixes type typeredef2 test (a lot
of work for one little syntax error). Unfortunately, it came at the cost
of requiring `>>` in front of state expressions on C-style functions
(QuakeC-style functions are unaffected). Also, there are now two
shift/reduce conflicts with structs and unions (but these same conflicts
are in gcc 3.4).
This has highlighted the need for having the equivalent of the
expression tree for the declaration system as there are now several
hacks to deal with the separation of types and declarators. But that's a
job for another week.
The grammar constructs for declarations come from gcc 3.4's parser (I
think it's the last version of gcc that used bison. Also, 3.4 is still
GPL 2, so no chance of an issue there).
While swizzle does work, it requires the source to be properly aligned
and thus is not really the best choice. The extend instruction has no
alignment requirements (at all) and thus is much better suited to
converting a scalar to a vector type.
Fixes#30
As a class's ivars are built up by inheritance, but with only that
class's ivars in the symbol table, is is necessary to include an offset
based on the super class's ivars in order to ensure alignments are
respected. This is achieved via the new `base` parameter to
build_struct(), which is used to offset the current size while
calculating the aligned offset of the symbols. The parameter is ignored
for unions, as they always start at 0. The ivars for the current class
still have a base offset of 0 until they are actually added to the
class.
Fixes#29
The alignment is specified as a power of 2 (ie, actual alignment = 1 <<
alignment) allowing old object files to be compatible (as their
alignment is 0). This is necessary for (in part for #30) as it turned
out even global vectors were not aligned correctly.
Currently, only data spaces even vaguely respect alignment. This may
need to be fixed in the future.
Most were pretty easy and fairly logical, but gib's regex was a bit of a
pain until I figured out the real problem was the conditional
assignments.
However, libs/gamecode/test/test-conv4 fails when optimizing due to gcc
using vcvttps2dq (which is nice, actually) for vector forms, but not the
single equivalent other times. I haven't decided what to do with the
test (I might abandon it as it does seem to be UD).
The destination operand must be a full four component vector, but the
source can be smaller and small sources do not need to be aligned: the
offset of the source operand and the swizzle indices are adjusted. The
adjustments are done during final statement emission in order to avoid
confusing the data flow analyser (and that's when def offsets are known).
Having three very similar sets of code for outputting values (just for
debug purposes even) got to be a tad annoying. Now there's only one, and
in the right place, too (with the other value code).
I'd created new_value_expr some time ago, but never used it...
Also, replace convert_* with cast_expr to the appropriate type (removes
a pile of value check and create code).
Use with quaternions and vectors is a little broken in that
vec4/quaternion and vec3/vector are not the same types (by design) and
thus a cast is needed (not what I want, though). However, creating
vectors (that happen to be int due to int constants) does seem to be
working nicely otherwise.
Nicely, I was able to reuse the generated conversion code used by the
progs engine to do the work in qfcc, just needed appropriate definitions
for the operand macros, and to set up the conversion code. Helped
greatly by the new value load/store functions.
pr_type_t now contains only the one "value" field, and all the access
macros now use their PACKED variant for base access, making access to
larger types more consistent with the smaller types.
In working with vectors and matrices while testing the scene wrappers, I
found that there was a fair bit of confusion about how large something
could be. Return values can be up to 32 words (but qfcc wasn't aware of
that), parameters were limited to 4 words still (and possibly should be
for varargs), and temp defs were limited to 8 words (1 lvec4). Temps are
used for handling return values (at least when not optimizing) and thus
must be capable of holding a return value, and passing large arguments
through *formal* parameters should be allowed. It seems reasonable to
limit parameter sizes to return value sizes.
A temp and a move are still used for large return values (4x4 matrix),
but that's an optimization issue: the code itself is at least correct.
Currently only via pragma (not command line options), but I needed to
test the concept. Converting legacy code is just too error prone.
Telling the compiler how to treat the operator makes more sense. When *
acts as @dot with Ruamoko progs, the result is automatically aliased as
a float as this is the legacy meaning (ie, float result for dot
product).
This is achieved by marking a void function with the void_return
attribute and then calling that function in an @return expression.
@return can be used only inside a void function and only with void
functions marked with the void_return attribute. As this is intended for
Objective-QC message forwarding, it is deliberately "difficult" to use
as returning a larger than expected value is unlikely to end well for
the calling function.
However, as a convenience, "@return nil" is allowed (in a void
function). It always returns an integer (which, of course,can be
interpreted as a pointer). This is safe because if the return value is
ignored, it will go into the progs return buffer, and if it is not
ignored, it is the smallest value that can be returned.
Having to remember to copy yet another specifier bit was getting
tedious, so use a union of a struct with the bitfields and an unsigned
int to access them in parallel. Makes for a tidier spec_merge, and one
less headache.
The command line option works the same way as
--advanced/traditional/extended, as does the pragma. As well, raumoko
(alternative spelling) can be used because both are legitimate and some
people may prefer one spelling over the other.
As always, use of the pragma is at one's own risk: its intended use is
forcing the target in the unit tests.
dvec4, lvec4 and ulvec4 need to be aligned to 8 words (32 bytes) in
order to avoid hardware exceptions. Rather than dealing with possibly
mixed alignment when a function has 8-word aligned locals but only
4-word aligned parameters, simply keep the stack frame 8-word aligned at
all times.
As for sizes, the temp def recycler was written before the Ruamoko ISA
was even a pipe dream and thus never expected temp def sizes over 4. At
least now any future adjustments can be done in one place.
My quick and dirty test program works :)
dvec4 xy = {1d, 2d, 0d, 0.5};
void printf(string fmt, ...) = #0;
int main()
{
dvec4 u = {3, 4, 3.14};
dvec4 v = {3, 4, 0, 1};
dvec4 w = v * xy + u;
printf ("[%g, %g, %g, %g]\n", w[0], w[1], w[2], w[3]);
return 0;
}
They're now properly part of the type system and can be used for
declaring variables, initialized (using {} block initializers), operated
on (=, *, + tested) though much work needs to be done on binary
expressions, and indexed. So far, only ivec2 has been tested.
Ruamoko passes va_list (@args) through the ... parameter (as such), but
IMP uses ... to defeat parameter type and count checking and doesn't
want va_list. While possibly not the best solution, adding a no_va_list
flag to function types and skipping ex_args entirely does take care of
the problem without hard-coding anything specific to IMP.
The system currently just sets some bits in the type specifier (the
attribute list should probably be carried around with the specifier),
but it gets the job done for now, and at least gets things started.
This makes it much easier to check (and more robust to name changes),
allowing for effectively killing the node to which the variable being
addressed is attached. This fixes the incorrect address being used for
va_list, which is what caused double-alias to fail.
Since Ruamoko progs must use lea to get the address of a local variable,
add use/def/kill references to the move instruction in order to inform
flow analysis of the variable since it is otherwise lost via the
resulting pointer (not an issue when direct var reference move can be
used).
The test and digging for the def can probably do with being more
aggressive, but this did nicely as a proof of concept.
This is necessary to get statement disassembly working, and likely
debugging in general. locals is the total size of the stack frame and
thus reaches above the function-entry stack pointer, and params_start is
the local space relative start of the parameters. Thus, knowing the
function-entry stack pointer, the bottom of the locals space can be
found by subtracting params_start, and the top of the locals space by
adding (locals - params_start).
This gets all the sections of the progs file nicely aligned and the code
easier to read with the offset and size calculations not being spread
through the function. ivar-struct-return now works when compiled for
Ruamoko.
The goal was to get lea being used for locals in ruamoko progs because
lea takes the base registers into account while the constant pointer
defs used by v6p cannot. Pointer defs are still used for gobals as they
may be out of reach of 16-bit addressing.
address_expr() has been simplified in that it no longer takes an offset:
the vast majority of the callers never passed one, and the few that did
have been reworked to use other mechanisms. In particular,
offset_pointer_expr does the manipulations needed to add an offset
(unscaled by type size) to a pointer. High-level pointer offsets still
apply a scale, though.
Alias expressions now do a better job of hanling aliasing of aliases by
simply replacing the target type when possible.
The parameter defs are allocated from the parameter space using a
minimum alignment of 4, and varargs functions get a va_list struct in
place of the ...
An "args" expression is unconditionally injected into the call arguments
list at the place where ... is in the list, with arguments passed
through ... coming after the ...
Arguments get through to functions now, but there's problems with taking
the address of local variables: currently done using constant pointer
defs, which can't work for the base register addressing used in Ruamoko
progs.
With the update to test-bi's printf (and a hack to qfcc for lea),
triangle.r actually works, printing the expected results (but -1 instead
of 1 for equality, though that too is actually expected). qfcc will take
a bit longer because it seems there are some design issues in address
expressions (ambiguity, and a few other things) that have pretty much
always been there.
While all base registers can be used for any purpose at any time (this
is why the with instruction has hard-absolute modes: you can never get
permanently lost), qfcc currently uses the convention of register 0 for
globals and register 1 for stack locals (params, locals, function args).
The register used to access a def is stored in the def and that is used
to set the register bits in the instruction opcode.
The def code actually doesn't know anything about any conventions: it
assumes all defs are global for non-temp defs (the function code updates
the defs before emitting code) and the current function provides the
register to use for any temp defs allocated while emitting code.
Seems to work well, but debug is utterly messed up (not surprised, that
will be tricky).
Still need to get the base register index into the instructions, but I
think this is it for basic code generation. I should be able to start
testing Ruamoko properly fairly soon :)
Thanks to the use/def/kill lists attached to statements for pseudo-ops,
it turned out to be a lot easier to implement flow analysis (and thus
dags processing) than I expected. I suspect I should go back and make
the old call code use them too, and probably several other places, as
that will greatly simplify the edge setting.
The means that the actual call expression is not in the statement lint
of the enclosing block expression, but just its result, whether the call
is void or not. This actually simplifies several things, but most
importantly will make Ruamoko calls easier to implement.
The test is because I had some trouble with double-calls, and is how I
found the return-postop issue :P
Since Ruamoko now uses the stack for parameters and locals, parameters
need to come after locals in the address space (instead of before, as in
v6 progs). Thus use separate spaces for parameters and locals regardless
of the target, then stitch them together appropriately for the target.
The third space is used for allocating stack space for arguments to
called functions. It us not used for v6 progs, and comes before locals
in Ruamoko progs.
Other than the return value, and optimization (ice, not implemented)
calls in Ruamoko look like they'll work.
This seems to be the most reasonable approach to allocating space for
function call parameters without using push and pop (or adding to the
stack pointer), though it's probably good even when using push and pop
to help keep things aligned.
Operand width is encoded in the instruction opcode, so the width needs
to be accounted for in order to select the correct instruction. With
this, my little test generates correct code for the ruamoko ISA (except
for return, still fails).
long is ignored for double, and v6p progs are stuck with 32 bits for
longs (don't feel like extending v6p any further), but the basics are
there for Ruamoko.
short is ignored for ints because the minimum size is 32, and signed is
just noise for ints anyway (and no chars, so...).
unsigned, however, is finally implemented properly (or at least seems to
be working correctly: tests pass after getting things compiling again,
and lt.u is used where it should be :)
And other related fields so integer is now int (and uinteger is uint). I
really don't know why I went with integer in the first place, but this
will make using macros easier for dealing with types.
They are both gone, and pr_pointer_t is now pr_ptr_t (pointer may be a
little clearer than ptr, but ptr is consistent with things like intptr,
and keeps the type name short).
This includes calls and unconditional jumps, relative and through a
table. The parameters are all lumped into the one object, with some
being unused by the different types (eg, args and ret_type used only by
call expressions). Just having nice names for the parameters (instead of
e1 and e2) makes it nice, even with all the sub-types lumped together.
No mysterious type aliasing bugs this time ;)
The move operator names are definitely obsolete (due to dropping the
expressions a year or two ago) and the precedence checks seem to be
handled elsewhere. Memset and state expressions went away a while back
too.
While this was a pain to get working, that pain only went to prove the
value of using proper "types" (even if only an enum) for different
expression types: just finding all the places to edit was a chore, and
easy to make mistakes (forgetting bits here and there).
Strangely enough, this exposed a pile of *type* aliasing bugs (next
commit).
At this stage, I doubt emit.c will need to know the details of the
target (v6, v6p, ruamoko) since the instruction formats are identical,
just different meanings for the opcode itself.
While qfcc dealing sensibly with mixed target VMs in the object files
has always been an outstanding issue, with the new instruction set it
has become a priority. Most importantly, this should allow QF to
continue building while I work on qfcc targeting the new IS.
It does little good for documentation to refer to fields that don't
exist (because a certain someone forgot to change the docs when changing
the field names, I wonder who :P).
And partial implementations in qfcc (most places will generate an
internal error (not implemented) or segfault, but some low-hanging fruit
has already been implemented).
The opcode table is a nightmare to maintain, but this does clean it up
and speed up opcode lookups since they can now be indexed. Of course, it
turns out I had missed adding several instructions, so had to fix that,
and qfcc needed a bit of a re-jigger to get the opcode out of the table.
qfo_to_progs was modifying the space data pointers in the input qfo,
making it impossible to reuse the qfo. However, qfo_relocate_refs needs
the updated pointers, thus do a shallow copy of the qfo and its spaces
(but not any of the data)
I decided that the check for whether control reaches the end of the
function without performing some necessary action (eg, invoking
[super dealoc] in a derived -dealoc) is conceptually the return
statement using a pseudo operand and the necessary action defining that
pseudo operand and thus is the same as checking for uninitialised
variables. Thus, add a pseudo operand type and use one to represent the
invocation of [super alloc], with a special function to call when the
"used" pseudo operand is "uninitialised".
While I currently don't know what else pseudo operands could be used
for, the system should be flexible enough to add any check.
Fixes#24
I want to use the function's pseudo address that was used for managing
aliased temporary variables for other pseudo operands as well. The new
name seems to better reflect the variable's purpose even without the
other pseudo operands as temporary variables are, effectively, pseudo
operands until they are properly allocated.
Forgetting to invoke [super dealloc] in a derived class's -dealloc
method has caused me to waste far too much time chasing down the
resulting memory leaks and crashes. This is actually the main focus of
issue #24, but I want to take care of multiple paths before I consider
the issue to be done.
However, as a bonus, four cases were found :)
While get_selector does the job of getting a selector from a selector
reference expression, I have long considered lumping various expression
types under ex_expr to be a mistake. Not only is this a step towards
sorting that out, it will make working on #24 easier.
In order to correctly handle swap-style code
{ t = a; a = b; b = t; }
edges need to be created for each of the assignments moving an
identifier lable, but the dag must remain acyclic (the above example
wants to create a cycle). Having the reachable nodes recorded makes
checking for potential loops a quick operation.
There's still some cleanup to do, but everything seems to be working
nicely: `make -j` works, `make distcheck` passes. There is probably
plenty of bitrot in the package directories (RPM, debian), though.
The vc project files have been removed since those versions are way out
of date and quakeforge is pretty much dependent on gcc now anyway.
Most of the old Makefile.am files are now Makemodule.am. This should
allow for new Makefile.am files that allow local building (to be added
on an as-needed bases). The current remaining Makefile.am files are for
standalone sub-projects.a
The installable bins are currently built in the top-level build
directory. This may change if the clutter gets to be too much.
While this does make a noticeable difference in build times, the main
reason for the switch was to take care of the growing dependency issues:
now it's possible to build tools for code generation (eg, using qfcc and
ruamoko programs for code-gen).
The compilation unit stores the directory from which qfcc was run and
any source files mentioned. This is similar to dwarf's compilation unit.
Right now, this is the only data in the new debug space, but more might
come in the future so it seems best to treat the debug space separately
in the object files.
getcwd is assumed to use malloc if its buff param is null. This may need
fixing in the future, but it's in one spot. The result in "saved" in the
non-progs pool.
It never really helped sort out the path issues when using build
directories. It worked well enough for single directory projects, but
things got messy very quickly, especially when mixing ruamoko libs with
external progs. A better method based on dwarf is coming.
It's not connected up yet because I'm unsure of just where to put things
(it gets messy fast), but just being able to see the structure of
complex types is nice.
This eases type unaliasing on functions a little.
Still more to to go, but this fixes a really hair-pulling bug: linux's
heap randomiser was making the typedef test fail randomly whenever
typedef.qfo was compiled.
When a type is aliased, the alias has two type chains: the simple type
chain with all other aliases stripped, and the full type chain. There
are still plenty of bugs in it, but having the clean type chain takes
care of the major issue that was in the previous attempt as only the
head of the type-chain needs to be skipped for type comparison.
Most of the bugs are in finding the locations where the head needs to be
skipped.
All simple type checks are now done using is_* helper functions. This
will help hide the implementation details of the type system from the
rest of the compiler (especially the changes needed for type aliasing).
That is, those created by operand_address. The dag code needs the
expression that is attached to the statement to have the correct
expression type in order to do the right thing with the operands and
aliasing, especially when generating temps. This fixes assignchain when
optimizing (all tests pass again).
Now convert_nil only assigns the nil expression a type, and nil makes
its way down to the statement emission code (where it belongs, really).
Breaks even more things :)
It's not possible to take the address of constants (at this stage) and
trying to use a move instruction with .zero as source would result in
the VM complaining about null pointer access when bounds checking is on.
Thus, don't convert a nil source expression until it is known to be
safe, and use memset when it is not.
This fixes the problem of using the return value of a function as an
element in a compound initializer. The cause of the problem is that
compound initializers were represented by block expressions, but
function calls are contained within block expressions, so def
initialization saw the block expression and thought it was a nested
compound initializer.
Technically, it was a bug in the nested element parsing code in that it
wasn't checking the result value of the block expression, but using a
whole new expression type makes things much cleaner and the work done
paves the way for labeled initializers and compound assignments.
Multi-line calls (especially messages) got rather confusing to read as
the lines jumped back and forth. Now the binding is better but the dags
code is reordering the parameters sometimes.
This reverts commit a2f203c840.
There is indeed a world of difference between "any" and "only", and it
helps if I read the rest of the docs AND the code :P.
While expression symbols worked for what they are, they weren't so good
for ivar access because every ivar of a class (and its super classes)
would be accessed at method scope creation, generating spurious access
errors if any were private. That is, when the access checks worked at
all.
This is for adding methods to classes and protocols via their interface,
not for adding methods by adding protocols (they still get copied).
Slightly more memory efficient.
Unlike gcc, qfcc requires foo to be defined, not just declared (I
suspect this is a bug in gcc, or even the ObjC spec), because allowing
forward declarations causes an empty (no methods) protocol to be
emitted, and then when the protocol is actually defined, one with
methods, resulting in two different versions of the same protocol, which
comments in the gnu objc runtime specifically state is a problem but is
not checked because it "never happens in practice" (found while
investigating gcc's behavior with @protocol and just what some of the
comments about static instance lists meant).
It proved to be too fragile in its current implementation. It broke
pointers to incomplete structs and switch enum checking, and getting it
to work for other things was overly invasive. I still want the encoding,
but need to come up with something more robust.a
Such declarations were being lost, thus in the following, the id field
never got added:
typedef struct qwaq_mevent_s {
int id;
int x, y, z;
int buttons;
} qwaq_mevent_t;
The addition of xdef data has made qfo_to_progs unusable in qfprogs,
resulting in various invalid memory accesses. It always was an ugly hack
anyway, so this is the first step to proper qfo support in qfprogs.
I was originally going to put it in the debug syms file, but I realized
that the data persistence code would need access to both def type and
certainly correct def offsets for defs in far data.
This far better reflects the actual meaning. It is very likely that
ty_none is a holdover from long before there was full type encoding and
it meant that the union in qfcc's type_t had no data. This is still
true for basic types, but only if not a function, field or pointer type.
If the type was function, field or pointer, it was not true, so it was
misnamed pretty much from the start.
The encoding is 3:5 giving 3 bits for alignment (log2) and 5 bits for
size, with alignment in the 3 most significant bits. This keeps the
format backwards compatible as until doubles were added, all types were
aligned to 1 word which gets encoded as 0, and the size is unaffected.
This fixed the uninitialized temp warning in HUD.r. The problem was
caused by the flow analyzer not being able to detect that the struct
temp was being initialized by the move statement due to the address of
the temp being in a pointer temp. While it would be good to use a
constant pointer for the address of the struct temp or improving the
flow analyzer to track actual data, avoiding the temp in the first place
results in nicer code as it removes a move statement.
Only as scalars, I still need to think about what to do for vectors and
quaternions due to param size issues. Also, doubles are not yet
guaranteed to be correctly aligned.
I don't remember what the goal was (stopped working on it eight months
ago), but some possibilities include:
- better handling of nil (have trouble with assigning into struts)
- automatic forward declarations ala C# and jai (I was watching vids
about jai at the time)
- something for pascal
- simply that the default symbol type should not be var (in which case,
goal accomplished)
Currently, they can represent either vectors or quaternions, and the
quaternions can be in either [s, v] form or [w, x, y, z] form.
Many things will not actual work yet as the vector expression needs to be
converted into the appropriate form for assigning the elements to the
components of the "vector" type.
This is a nice feature found in fteqcc (also a bit of a challenge from
Spike). Getting bison to accept the new expression required rewriting the
state expression grammar, so this is mostly for the state expression. A
test to ensure the state expression doesn't break is included.
