mirror of
https://github.com/ZDoom/raze-gles.git
synced 2024-12-27 04:00:42 +00:00
718112a8fe
Currently none of these is being used, but eventually they will, once more code gets ported over. So it's better to have them right away and avoid editing the project file too much, only to revert that later.
395 lines
11 KiB
C++
395 lines
11 KiB
C++
// Game_Music_Emu https://bitbucket.org/mpyne/game-music-emu/
|
|
|
|
#include "Ay_Apu.h"
|
|
|
|
/* Copyright (C) 2006 Shay Green. This module is free software; you
|
|
can redistribute it and/or modify it under the terms of the GNU Lesser
|
|
General Public License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version. This
|
|
module is distributed in the hope that it will be useful, but WITHOUT ANY
|
|
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
|
|
FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more
|
|
details. You should have received a copy of the GNU Lesser General Public
|
|
License along with this module; if not, write to the Free Software Foundation,
|
|
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA */
|
|
|
|
#include "blargg_source.h"
|
|
|
|
// Emulation inaccuracies:
|
|
// * Noise isn't run when not in use
|
|
// * Changes to envelope and noise periods are delayed until next reload
|
|
// * Super-sonic tone should attenuate output to about 60%, not 50%
|
|
|
|
// Tones above this frequency are treated as disabled tone at half volume.
|
|
// Power of two is more efficient (avoids division).
|
|
unsigned const inaudible_freq = 16384;
|
|
|
|
int const period_factor = 16;
|
|
|
|
static byte const amp_table [16] =
|
|
{
|
|
#define ENTRY( n ) byte (n * Ay_Apu::amp_range + 0.5)
|
|
// With channels tied together and 1K resistor to ground (as datasheet recommends),
|
|
// output nearly matches logarithmic curve as claimed. Approx. 1.5 dB per step.
|
|
ENTRY(0.000000),ENTRY(0.007813),ENTRY(0.011049),ENTRY(0.015625),
|
|
ENTRY(0.022097),ENTRY(0.031250),ENTRY(0.044194),ENTRY(0.062500),
|
|
ENTRY(0.088388),ENTRY(0.125000),ENTRY(0.176777),ENTRY(0.250000),
|
|
ENTRY(0.353553),ENTRY(0.500000),ENTRY(0.707107),ENTRY(1.000000),
|
|
|
|
/*
|
|
// Measured from an AY-3-8910A chip with date code 8611.
|
|
|
|
// Direct voltages without any load (very linear)
|
|
ENTRY(0.000000),ENTRY(0.046237),ENTRY(0.064516),ENTRY(0.089785),
|
|
ENTRY(0.124731),ENTRY(0.173118),ENTRY(0.225806),ENTRY(0.329032),
|
|
ENTRY(0.360215),ENTRY(0.494624),ENTRY(0.594624),ENTRY(0.672043),
|
|
ENTRY(0.766129),ENTRY(0.841935),ENTRY(0.926882),ENTRY(1.000000),
|
|
// With only some load
|
|
ENTRY(0.000000),ENTRY(0.011940),ENTRY(0.017413),ENTRY(0.024876),
|
|
ENTRY(0.036318),ENTRY(0.054229),ENTRY(0.072637),ENTRY(0.122388),
|
|
ENTRY(0.174129),ENTRY(0.239303),ENTRY(0.323881),ENTRY(0.410945),
|
|
ENTRY(0.527363),ENTRY(0.651741),ENTRY(0.832338),ENTRY(1.000000),
|
|
*/
|
|
#undef ENTRY
|
|
};
|
|
|
|
static byte const modes [8] =
|
|
{
|
|
#define MODE( a0,a1, b0,b1, c0,c1 ) \
|
|
(a0 | a1<<1 | b0<<2 | b1<<3 | c0<<4 | c1<<5)
|
|
MODE( 1,0, 1,0, 1,0 ),
|
|
MODE( 1,0, 0,0, 0,0 ),
|
|
MODE( 1,0, 0,1, 1,0 ),
|
|
MODE( 1,0, 1,1, 1,1 ),
|
|
MODE( 0,1, 0,1, 0,1 ),
|
|
MODE( 0,1, 1,1, 1,1 ),
|
|
MODE( 0,1, 1,0, 0,1 ),
|
|
MODE( 0,1, 0,0, 0,0 ),
|
|
};
|
|
|
|
Ay_Apu::Ay_Apu()
|
|
{
|
|
// build full table of the upper 8 envelope waveforms
|
|
for ( int m = 8; m--; )
|
|
{
|
|
byte* out = env.modes [m];
|
|
int flags = modes [m];
|
|
for ( int x = 3; --x >= 0; )
|
|
{
|
|
int amp = flags & 1;
|
|
int end = flags >> 1 & 1;
|
|
int step = end - amp;
|
|
amp *= 15;
|
|
for ( int y = 16; --y >= 0; )
|
|
{
|
|
*out++ = amp_table [amp];
|
|
amp += step;
|
|
}
|
|
flags >>= 2;
|
|
}
|
|
}
|
|
|
|
output( 0 );
|
|
volume( 1.0 );
|
|
reset();
|
|
}
|
|
|
|
void Ay_Apu::reset()
|
|
{
|
|
last_time = 0;
|
|
noise.delay = 0;
|
|
noise.lfsr = 1;
|
|
|
|
osc_t* osc = &oscs [osc_count];
|
|
do
|
|
{
|
|
osc--;
|
|
osc->period = period_factor;
|
|
osc->delay = 0;
|
|
osc->last_amp = 0;
|
|
osc->phase = 0;
|
|
}
|
|
while ( osc != oscs );
|
|
|
|
for ( int i = sizeof regs; --i >= 0; )
|
|
regs [i] = 0;
|
|
regs [7] = 0xFF;
|
|
write_data_( 13, 0 );
|
|
}
|
|
|
|
void Ay_Apu::write_data_( int addr, int data )
|
|
{
|
|
assert( (unsigned) addr < reg_count );
|
|
|
|
if ( (unsigned) addr >= 14 )
|
|
{
|
|
#ifdef debug_printf
|
|
debug_printf( "Wrote to I/O port %02X\n", (int) addr );
|
|
#endif
|
|
}
|
|
|
|
// envelope mode
|
|
if ( addr == 13 )
|
|
{
|
|
if ( !(data & 8) ) // convert modes 0-7 to proper equivalents
|
|
data = (data & 4) ? 15 : 9;
|
|
env.wave = env.modes [data - 7];
|
|
env.pos = -48;
|
|
env.delay = 0; // will get set to envelope period in run_until()
|
|
}
|
|
regs [addr] = data;
|
|
|
|
// handle period changes accurately
|
|
int i = addr >> 1;
|
|
if ( i < osc_count )
|
|
{
|
|
blip_time_t period = (regs [i * 2 + 1] & 0x0F) * (0x100L * period_factor) +
|
|
regs [i * 2] * period_factor;
|
|
if ( !period )
|
|
period = period_factor;
|
|
|
|
// adjust time of next timer expiration based on change in period
|
|
osc_t& osc = oscs [i];
|
|
if ( (osc.delay += period - osc.period) < 0 )
|
|
osc.delay = 0;
|
|
osc.period = period;
|
|
}
|
|
|
|
// TODO: same as above for envelope timer, and it also has a divide by two after it
|
|
}
|
|
|
|
int const noise_off = 0x08;
|
|
int const tone_off = 0x01;
|
|
|
|
void Ay_Apu::run_until( blip_time_t final_end_time )
|
|
{
|
|
require( final_end_time >= last_time );
|
|
|
|
// noise period and initial values
|
|
blip_time_t const noise_period_factor = period_factor * 2; // verified
|
|
blip_time_t noise_period = (regs [6] & 0x1F) * noise_period_factor;
|
|
if ( !noise_period )
|
|
noise_period = noise_period_factor;
|
|
blip_time_t const old_noise_delay = noise.delay;
|
|
blargg_ulong const old_noise_lfsr = noise.lfsr;
|
|
|
|
// envelope period
|
|
blip_time_t const env_period_factor = period_factor * 2; // verified
|
|
blip_time_t env_period = (regs [12] * 0x100L + regs [11]) * env_period_factor;
|
|
if ( !env_period )
|
|
env_period = env_period_factor; // same as period 1 on my AY chip
|
|
if ( !env.delay )
|
|
env.delay = env_period;
|
|
|
|
// run each osc separately
|
|
for ( int index = 0; index < osc_count; index++ )
|
|
{
|
|
osc_t* const osc = &oscs [index];
|
|
int osc_mode = regs [7] >> index;
|
|
|
|
// output
|
|
Blip_Buffer* const osc_output = osc->output;
|
|
if ( !osc_output )
|
|
continue;
|
|
osc_output->set_modified();
|
|
|
|
// period
|
|
int half_vol = 0;
|
|
blip_time_t inaudible_period = (blargg_ulong) (osc_output->clock_rate() +
|
|
inaudible_freq) / (inaudible_freq * 2);
|
|
if ( osc->period <= inaudible_period && !(osc_mode & tone_off) )
|
|
{
|
|
half_vol = 1; // Actually around 60%, but 50% is close enough
|
|
osc_mode |= tone_off;
|
|
}
|
|
|
|
// envelope
|
|
blip_time_t start_time = last_time;
|
|
blip_time_t end_time = final_end_time;
|
|
int const vol_mode = regs [0x08 + index];
|
|
int volume = amp_table [vol_mode & 0x0F] >> half_vol;
|
|
int osc_env_pos = env.pos;
|
|
if ( vol_mode & 0x10 )
|
|
{
|
|
volume = env.wave [osc_env_pos] >> half_vol;
|
|
// use envelope only if it's a repeating wave or a ramp that hasn't finished
|
|
if ( !(regs [13] & 1) || osc_env_pos < -32 )
|
|
{
|
|
end_time = start_time + env.delay;
|
|
if ( end_time >= final_end_time )
|
|
end_time = final_end_time;
|
|
|
|
//if ( !(regs [12] | regs [11]) )
|
|
// debug_printf( "Used envelope period 0\n" );
|
|
}
|
|
else if ( !volume )
|
|
{
|
|
osc_mode = noise_off | tone_off;
|
|
}
|
|
}
|
|
else if ( !volume )
|
|
{
|
|
osc_mode = noise_off | tone_off;
|
|
}
|
|
|
|
// tone time
|
|
blip_time_t const period = osc->period;
|
|
blip_time_t time = start_time + osc->delay;
|
|
if ( osc_mode & tone_off ) // maintain tone's phase when off
|
|
{
|
|
blargg_long count = (final_end_time - time + period - 1) / period;
|
|
time += count * period;
|
|
osc->phase ^= count & 1;
|
|
}
|
|
|
|
// noise time
|
|
blip_time_t ntime = final_end_time;
|
|
blargg_ulong noise_lfsr = 1;
|
|
if ( !(osc_mode & noise_off) )
|
|
{
|
|
ntime = start_time + old_noise_delay;
|
|
noise_lfsr = old_noise_lfsr;
|
|
//if ( (regs [6] & 0x1F) == 0 )
|
|
// debug_printf( "Used noise period 0\n" );
|
|
}
|
|
|
|
// The following efficiently handles several cases (least demanding first):
|
|
// * Tone, noise, and envelope disabled, where channel acts as 4-bit DAC
|
|
// * Just tone or just noise, envelope disabled
|
|
// * Envelope controlling tone and/or noise
|
|
// * Tone and noise disabled, envelope enabled with high frequency
|
|
// * Tone and noise together
|
|
// * Tone and noise together with envelope
|
|
|
|
// This loop only runs one iteration if envelope is disabled. If envelope
|
|
// is being used as a waveform (tone and noise disabled), this loop will
|
|
// still be reasonably efficient since the bulk of it will be skipped.
|
|
while ( 1 )
|
|
{
|
|
// current amplitude
|
|
int amp = 0;
|
|
if ( (osc_mode | osc->phase) & 1 & (osc_mode >> 3 | noise_lfsr) )
|
|
amp = volume;
|
|
{
|
|
int delta = amp - osc->last_amp;
|
|
if ( delta )
|
|
{
|
|
osc->last_amp = amp;
|
|
synth_.offset( start_time, delta, osc_output );
|
|
}
|
|
}
|
|
|
|
// Run wave and noise interleved with each catching up to the other.
|
|
// If one or both are disabled, their "current time" will be past end time,
|
|
// so there will be no significant performance hit.
|
|
if ( ntime < end_time || time < end_time )
|
|
{
|
|
// Since amplitude was updated above, delta will always be +/- volume,
|
|
// so we can avoid using last_amp every time to calculate the delta.
|
|
int delta = amp * 2 - volume;
|
|
int delta_non_zero = delta != 0;
|
|
int phase = osc->phase | (osc_mode & tone_off); assert( tone_off == 0x01 );
|
|
do
|
|
{
|
|
// run noise
|
|
blip_time_t end = end_time;
|
|
if ( end_time > time ) end = time;
|
|
if ( phase & delta_non_zero )
|
|
{
|
|
while ( ntime <= end ) // must advance *past* time to avoid hang
|
|
{
|
|
int changed = noise_lfsr + 1;
|
|
noise_lfsr = (-(noise_lfsr & 1) & 0x12000) ^ (noise_lfsr >> 1);
|
|
if ( changed & 2 )
|
|
{
|
|
delta = -delta;
|
|
synth_.offset( ntime, delta, osc_output );
|
|
}
|
|
ntime += noise_period;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
// 20 or more noise periods on average for some music
|
|
blargg_long remain = end - ntime;
|
|
blargg_long count = remain / noise_period;
|
|
if ( remain >= 0 )
|
|
ntime += noise_period + count * noise_period;
|
|
}
|
|
|
|
// run tone
|
|
end = end_time;
|
|
if ( end_time > ntime ) end = ntime;
|
|
if ( noise_lfsr & delta_non_zero )
|
|
{
|
|
while ( time < end )
|
|
{
|
|
delta = -delta;
|
|
synth_.offset( time, delta, osc_output );
|
|
time += period;
|
|
//phase ^= 1;
|
|
}
|
|
//assert( phase == (delta > 0) );
|
|
phase = unsigned (-delta) >> (CHAR_BIT * sizeof (unsigned) - 1);
|
|
// (delta > 0)
|
|
}
|
|
else
|
|
{
|
|
// loop usually runs less than once
|
|
//SUB_CASE_COUNTER( (time < end) * (end - time + period - 1) / period );
|
|
|
|
while ( time < end )
|
|
{
|
|
time += period;
|
|
phase ^= 1;
|
|
}
|
|
}
|
|
}
|
|
while ( time < end_time || ntime < end_time );
|
|
|
|
osc->last_amp = (delta + volume) >> 1;
|
|
if ( !(osc_mode & tone_off) )
|
|
osc->phase = phase;
|
|
}
|
|
|
|
if ( end_time >= final_end_time )
|
|
break; // breaks first time when envelope is disabled
|
|
|
|
// next envelope step
|
|
if ( ++osc_env_pos >= 0 )
|
|
osc_env_pos -= 32;
|
|
volume = env.wave [osc_env_pos] >> half_vol;
|
|
|
|
start_time = end_time;
|
|
end_time += env_period;
|
|
if ( end_time > final_end_time )
|
|
end_time = final_end_time;
|
|
}
|
|
osc->delay = time - final_end_time;
|
|
|
|
if ( !(osc_mode & noise_off) )
|
|
{
|
|
noise.delay = ntime - final_end_time;
|
|
noise.lfsr = noise_lfsr;
|
|
}
|
|
}
|
|
|
|
// TODO: optimized saw wave envelope?
|
|
|
|
// maintain envelope phase
|
|
blip_time_t remain = final_end_time - last_time - env.delay;
|
|
if ( remain >= 0 )
|
|
{
|
|
blargg_long count = (remain + env_period) / env_period;
|
|
env.pos += count;
|
|
if ( env.pos >= 0 )
|
|
env.pos = (env.pos & 31) - 32;
|
|
remain -= count * env_period;
|
|
assert( -remain <= env_period );
|
|
}
|
|
env.delay = -remain;
|
|
assert( env.delay > 0 );
|
|
assert( env.pos < 0 );
|
|
|
|
last_time = final_end_time;
|
|
}
|