This bypasses set_new, but completely removes the use of the global lock
from within RecursiveClusterFlow. This seems to give a small speedup: 203
seconds threaded.
This was testing an idea I had to remove the plane flips. It seems to have
been good for the initial plane orientation, but was a slight slowdown for
the pass-portal test. However, this makes the code a little easier to work
with for my idea on improving the algorithm itself.
Since the stack structure in the thread data is a linked list, move the
stack blocks off the program stack and into malloced memory. More
importantly, when the stack block is allocated, the mightsee working set is
allocated too, and as neither are freed, this greatly reduces contention
for the lock. Also, because the memory is kept, single threaded time for
gmsp3v2 dropped from 695s to 670s. Threaded is now about 207s (down from
350).
While using set operators was clearer, it was rather expensive (about 25s
for gmsp3v2). qfvis now completes the map in about 695s (single threaded).
About 15s faster than tyr for the same conditions (1 thread, level 4).
This is the second part of the separator search optimization from tyrutils
vis. With this, qfvis is getting close to tyrutils vis when
running single threaded (qfvis is suffering some nasty thread contention
and thus can't get below about 350 seconds with 4 threads). 808s vs 707s.
Interesting, it makes very little (maybe faster) difference to find all the
separators for levels 3 and 4. This might be due to the higher levels using
most of the planes to fully clip source away. Anyway, it makes the code a
little clearer (one function, one task).
I had forgotten to skip the refined tests when the sphere was entirely on
the relevant side of the plane. Now BasePortalVis for gmsp3v2 takes 11s on
my machine (it was 13 with the previous optimization and 15.9 before that).
Also, write some comments describing how BasePortalVis works.
Representing the side of the plane on which the sphere lies is much more
useful as more complicated tests can be done using just the one call.
-1: the sphere is entirely on the back side of the plane
0: the sphere is intersecting the plane
1: the sphere is entirely on the front side of the plane
It was supposed to be 2, but for some reason I neglected to set it when I
set up the options parsing. However, level 4 is the standard for production
maps, and it happens to be faster than level 2 (at least for gmsp3v2.bsp)
I think the reason I didn't think of that when I tried to improve qfvis's
performance many years ago is I just simply did not understand
ClipToSeparators. However, the difference caching the separators makes is
phenomenal. Before the change, single threaded qfvis would get stuck on one
particular portal for at least a day (I gave up waiting), but now even a
debug build will complete gmsp3v2.bsp in less than 12 minutes (4 threads on
my quad-core). And that's at level 2! Getting stuck for a day was at level
0.
While noticeably slower than the previous expanded set manipulation code,
this is much easier to read. I can worry about optimizing the set code when
I get qfvis behaving better.
All of the nastiness is hidden in bspfile.c (including the old bsp29
specific data types). However, the conversions between bsp29 and bsp2 are
implemented but not yet hooked up properly. This commit just gets the data
structures in place and the obvious changes necessary to the rest of the
engine to get it to compile, plus a few obvious "make it work" changes.
Unfortunately, just because the header is there doesn't mean anything will
actually work :(. Also, the check is based on the host vendor/os for now.
Yes, it's rather lame but it will do for now.
With this, QF will build on an almost fresh ps3toolchain install. Only two
"fixes" are needed:
o In $PS3DEV/ppu/powerpc64-ps3-elf: ln -s ../include sys-include
o libsamplerate cross-built and installed.
I got rather tired of there being multiple definitions of mostly compatible
plane types (and I need a common type anyway). dplane_t still exists for
now because I want to be careful when messing with the actual bsp format.
Make the params for FreeWinding and CopyWinding consistent with those in
qfbsp. This fixes some doxygen warnings while I think about how best to
handle the duplicate code.
Most of the guts of configure.ac have been moved to config.d and are then
brought in by m4_include. This will make maintaining configure.ac much easier.
Also drop use of PROGRAM and VERSION, using PACKAGE_NAME, PACKAGE_VERSION, and
on occasion, PACKAGE_STRING instead, and clean out some old files we no longer
need.
